Tercoo 4101008 Offers

MULTI 8 Disc Rotating Blaster Disc Tercoo is a rotating disc for the removal of paint, rust, mill scale, welding slag, tar, epoxy and adhesives from materials such as steel, iron, fiberglass, concrete or stone. Tercoo provides the correct surface preparation for the proper adhesion of new protective coatings. Tercoo is a natural rubber disc with 12 tungsten carbide tips. Centrifugal force causes the flexible rubber disc to react so that it creates a hammer effect similar to sandblasting. The flexibility ensures that the tips clean the surface perfectly.

The rotating blaster discs have these advantages over sandblasting: no set up time easier to use in smaller, confined areas this method is portable do not have to bring the job to the sandblaster a much cleaner work environment both during and upon completion of the job just as fast or faster than sandblasting Tercoo rotating discs do not create any heat, so tough materials such as tar, adhesives and sealants will be easily removed.

No matter what the coating, Tercoo always cleans and the airborne particulates are tremendously reduced compared to other methods. Tercoo removes rust. Since no heat is created, Tercoo rotating blaster discs open the metal pores to pull out rust. Wire brushes, wire fingers and flap wheels remove some surface rust, but the heat generated closes the metal pores and imbeds unremoved rust that will eventually rise through the surface coating.

Features

• A MULTI 8 disc set covers a 250 to 300 square meter area with proper use and dependent upon the material being removed
• Powered by either a fein electric polisher (part number 4001009) operating up to 2500 rpm, a makita electric polisher (part number 4001010) operating up to 3000 rpm or an IR air angle polisher (part number 4001011)
• Operating up to 2500 rpm, each of these power sources is specially adapted, for safety reasons, to work with the tercoo MULTI 8 disc rotating blaster set
• Each disc in the MULTI 8 disc set is individually replaceable, the MULTI 8 disc consists of four sets of two different single discs that are adjacent to each other, one disc is standard (part number 4101004) and the other (part number 4101005) is offset 15°s
• Removes rust, old paint, tar, epoxy, and mill scale from steel, iron, concrete, and stone
• Delivers a result similar to sandblasting (Sa 2.5–3.0) without the dust or mess, leaving the surface ready for new coatings
• Designed for use with high-torque machines

Applications

• Shipping tercoo rotating blaster discs are excellent for maintaining your boat or ship. remove old paint, rust, tar and the build-up of contaminants
• Offshore tercoo rotating blaster discs are excellent for repairing and maintaining offshore installations where waterproof coatings are present
• Manufacturing tercoo rotating blaster discs are excellent for removing mill scale before or after welding and prior to painting
• Industry tercoo rotating blaster discs are excellent for cleaning welding seams, even in small spaces, because few or no sparks are created
• Construction tercoo rotating blaster discs are excellent for cleaning concrete and rubber where chlorine compounds are now used
• Autobody tercoo removes undercoating

• The Tercoo rotating blaster disc(s) work best if moved in a slightly elliptical motion when going back and forth across the work surface
• Operate the Tercoo rotating blaster disc(s) at a 90° angle relative to the direction in which the carbide tips are pointed, same direction in which the disc shaft is pointed
• The Tercoo SINGLE rotating blaster disc will work in contoured areas. Slow your power source down to approximately 1000 to 1250 rpm. This will reduce the centrifugal force and allow the disc to flex and clean without chattering
• Mount the Tercoo rotating blaster disc in the power source as directed by the literature supplied by the tool manufacturer
• The Tercoo rotating blaster disc should always be used at a 90° angle relative to the work surface
• Apply minimal pressure to the work surface. More pressure equals more wear which will reduce the life of the rotating blaster disc(s)
• If there is a seam or weld in the work surface then the rotating blaster disc should be moved in a direction parallel to the weld or seam without crossing the weld or seam perpendicularly